How do you cut slate?

How to Cut Slate Tile With A Jig Saw?

If you are looking for how to cut slate tile with a jigsaw then you have come to right place. If you want to learn how to cut slate tile with a jigsaw then read on. You will get all the information that you need from our blog post. This is one of the most popular questions which is why we wrote it!

We are going to share everything that we know about how to cut slate tile with a jigsaw. There are many different ways of doing it and there is no right or wrong way. All you have to do is follow these simple steps:

1) Find a good spot where you can see the edge of the slate flooring. You don’t want to accidentally hit any sharp edges while trying to cut it.

2) Lay out your saw blade so that when you start cutting it, the slate tiles will fall into the blades. You can use a piece of scrap wood if you like but make sure that it’s not too thick because otherwise you might miss some pieces.

3) Start at one end and work your way around until you reach the other side. Do this slowly so that there won’t be any mistakes during the process. If you are doing this by yourself then it would be a good idea to put one foot on one side of the tile and push down so that you don’t get any up and down motion when using the jigsaw. The first time you do this it will most likely be slow going because you have to keep stopping to remove all the tiny pieces of slate from the saw blade.

4) Try to cut the tiles as straight as possible because this will help keep them from breaking apart when you are removing them from the floor later. If you have a lot of tile rooms then you can always use a hammer and chisel to break up the bigger pieces once you have them removed. Just make sure to put something underneath it first to prevent damaging the floor underneath.

There you have it. That is how you cut slate tile with a jigsaw. Now that you have all the slate removed, you can start putting down your new flooring. This will help protect your subfloor as well as make the room look better.

Do You Cut Slate With A Jigsaw?

Have you ever needed to know how to cut slate tile with a jigsaw? Well if so then this is the guide for you. We will be teaching you how to cut slate tile with a jigsaw all in this one simple guide.

Learning how to cut slate tile with a jigsaw isn’t all that hard. It can prove a little difficult if you have never done any type of DIY in the past, but anyone can learn how to cut slate tile with a jigsaw with a little bit of effort and patience. All you need is a few simple tools and you’ll be ready to get started on your slate tile cutting project.

Step One: Collect Your Tools

To gather all of your tools you’re going to want to head to your local hardware store or home improvement center. You’re going to see aisles and aisles of different tools and you’re not exactly sure what you’ll need. All you know is that you need tools for cutting slate tile, but not just any tools; you need power tools. The power tools you can get away with not buying are the ones that plug into the wall because well that won’t be very practical while trying to cut slate tile would it? Here is a list of the tools you’ll need and a description of what they do.

how do you cut slate on remodelingmate.com

 Jigsaw: This is a power saw that will help you cut out your shapes in the slate tile. It is also called a saber saw.

 Drill: This is an electric screwdriver that can drill through wood, metal and even specialized materials like tile if needed.

 Hammer: Any old hammer will do. You’re going to want to be able to break up the tile once you’re finished cutting it.

 Chisel: This is the tool you’ll use to break up the slate tile if you don’t have a hammer or you feel a hammer would do more harm than good to your tiles.

 Level: Any old level will do as well. You’re going to use this to ensure your tiles are straight and even with each other.

Step Two: Prep The Area

Now that you have all your tools, you’re going to need to prep the area. This means you’re going to need to tape plastic over all the windows and any other open area where you don’t want the dust to get in. All you really need to do is lay down a layer of plastic big enough to cover the floor and the majority of the walls.

Step Three: Cut Out The Pieces

Now this is the step where you’re going to be doing all the cutting out of the individual pieces of slate tile. This can prove to take awhile depending on how many individual pieces, their shapes and sizes as well as how much waste you want to have. All of this is going to depend on you and what exactly you want to do with your tiles. But for now let’s just focus on the cutting.

The way you’re going to start is by placing the piece of slate on some type of stand so that it’s elevated off the ground. This will prevent the dust from getting all over the floor. Now depending on the type of jigsaw you have will determine how you should hold and maneuver it. If you have an electric one, then all you need to do is apply some pressure with your finger on the trigger and guide the tip of the blade along the lines of your template.

Now if you have a manual jigsaw, then it’s a little different. What you want to do is place your thumb on the tip of the blade as to provide the pressure needed to cut and then use your other four fingers and guide the jigsaw along the lines.

how do you cut slate from our website

Step Four: Breaking Up The Pieces

Now that you’ve finished cutting out all your pieces and you’re left with a mess of slate tile pieces that are all connected by very thin strips of slate. What you need to do now is remove and dispose of these strips of slate so that you’re left with individual pieces that are all separate from one another.

To do this you’re going to need a chisel and a hammer. Using the chisel push it into the crack of two slate tile pieces and hammer it in. The idea is to force the blade of the chisel into the crack and break up the cement holding the two pieces together. Continue doing this with all the other tile pieces.

Step Five: Clean Up

The last thing you need to do is clean up your entire work area. This means gathering up all the plastic you used to protect your working area and take it out to the trash along with the leftover slate pieces and all your tools.

You can either throw away or recycle (depends on where you live and the laws) the plastic, slate pieces and your tools as this is all very heavy and you don’t want to be carrying this around while doing the next step.

Step Six: Applying The Grout

Now for this step you’re going to need a grout bag and a bucket of water. Fill the bag up about half way with grout. The type of grout you use is going to be dependent on what color tile you’re applying it to as well as what you want it to look like when finished.

If you’re doing a floor then you probably want a color that matches the tile’s color as close as possible, if it’s a wall then you can use a lighter color to give the appearance of more light in the room.

In any case, squeeze the grout from the bag onto the tile. Use a large metal spatula to spread the grout out into all the right spaces. Do this for all the tiles you need to cover then allow it to dry. This is going to take at least a whole day so plan accordingly.

To get an even coating you might have to apply the grout on some tiles more than once. Letting it sit over night may help dry it up a bit before wiping it off the next day.

how do you cut slate at remodelingmate.com

Grouting is definitely one of the more time consuming parts of this project but must be done if you want to avoid having that unsightly white line between the tiles and the floor or wall. It’s best to do this task in a well-ventilated area as the dust from the grout can get in your eyes and cause discomfort.

Step Seven: Curing

After applying the grout to all your tile pieces and spreading it evenly across all the tiles you need to cover, you’re ready to allow it to dry. You don’t need to place these in the sun or put any sort of fan blowing on them. Just leave them alone and they’ll be good as new in a couple days.

The next thing you’re going to want to do is clean up. If you haven’t thrown away the left over tile pieces, plastic sheets and other tools from your work then do so. Make sure you dispose of them where they won’t get in the way of any animals that may decide to eat the plastic or get stepped on by any unsuspecting person.

If you have any grout left over then make sure to save it in a ziplock bag for later use.

Step Eight: Applying Sealant

Once the grout has dried for at least 48 hours, you can then apply the sealant. Getting the right sealant is probably the most important part of this process. The wrong sealant and you might as well have not sealed the floor at all because it will eventually get destroyed by either moisture or UV rays (depending on the type of sealant you used).

If you’re sealing a floor then make sure to get a sealant that’s made especially for floors. If you’re sealing a tile wall then get one that’s made for walls. Using the wrong sealant will not only diminish the life span of your seal but it’ll also look terrible and not create that smooth shiny finish that you want.

Follow the directions on the sealant container for applying it to your floor or wall. Make sure to get it into all the little cracks and crevasses so that you don’t get any moisture in those areas.

how do you cut slate at remodelingmate.com

The most important thing is to not apply too much of the sealant. Applying too much will make the floor or wall look wet or shiny and you definitely don’t want that because it doesn’t look good and makes it difficult to clean.

Allow the sealant to dry then you’re done!

Step Nine: Maintenance

Once your floor or wall is sealed, you never have to do anything to it again unless you scrape, damage or stain it. Sealing it once will keep it looking nice and new for many years to come. Should you ever need to clean it, all you need is some warm water and mild soap. Don’t use harsh chemicals because they can damage the seal.

If water gets trapped in between your tiles and walls then it’s not a big deal because the sealant will prevent it from causing any damage. The only thing you should do is use a wet/dry vacuum to suck out as much of the water as you can. You don’t want to use a mop on your brand new floor or wall because that could force moisture deeper into the surface and cause problems.

Now that you’ve sealed your floor or wall, you can do whatever you want on top of it such as laying down vinyl, linoleum, carpet, or hardwood floor. You could also lay down tile directly on top of your new wall or floor if you prefer.

You can also use the same process to protect outdoor tiles and bricks, such as those used for a patio or walkway. Sealing outdoor tiles is just as easy as sealing indoor ones and it will keep them from getting damaged due to exposure to the elements.

You can use the same process to seal bath tubs, sinks and other tile or glass fixtures. Sealing these will make them easier to keep clean and prevent stains from setting in as well.

If you do get a stain on your new floor or wall then don’t try to scrub it out because you’ll probably make it worse. Simply put a little carpet cleaner on the stain with a rag then use a blow dryer to dry it. The heat from the dryer will cause the stain to lift right up. Be sure to test this method in an inconspicuous place first to make sure the carpet cleaner doesn’t damage the sealer.

If you have vinyl or linoleum flooring, then you can use the same process for bath tubs and sinks listed above. Just apply some of the cleaner to the stain then use a blow dryer to dry it. It won’t lift the stain entirely, but it will lessen its appearance significantly and make the rest of the stain much easier to clean.

By taking proper care of your floor or wall, it will keep looking great and have a nice shine without ever having to polish it. Your floor or wall will also be a breeze to keep clean which will save you a lot of time because you won’t have to scrub dried on spills or stains as often.

If you would like to learn more about how you can protect your tile floor or wall, please contact a company like Tiles by Pat.

Sources & references used in this article: