How do you level fence posts?

How do you Level Fence Posts?

Leveling fence posts is one of the most common tasks when it comes to building fences. There are many different ways to level fence posts. You may use a hand trowel or a power mower blade, but there are other methods which you need not worry about.

One way of leveling fence posts is using a circular saw with a circular file. Another method is to use a circular saw with a reciprocating saw. A third method is to use a jig and jigsaw.

The first thing you need to know before starting to level fence posts is that you must have good footing. If your fence does not reach all the way down into the ground, then you will not be able to level it properly. Also, if you are working on a slope, then you need to make sure that the fence reaches all the way down into the ground.

A circular saw is used to cut out the top of each post so that they can be leveled. You could also use a power mower blade to level them. A circular saw with a reciprocating saw would allow you to cut out two sides at once and then move onto another side later on.

Using a jig and a jigsaw you could cut out one side without moving the saw at all.

You may use several types of methods, depending on your situation and preference. You may need to redrill holes for the posts if you are using the reciprocating saw or jigsaw method. Be sure to measure the height of the post before and after you cut it so that you can fill it back in with dirt when you are done leveling it.

Raking the cut dirt back into the trench

If you need to redrill the holes, be sure to use the right sized bit for the diameter of the post you are using. After re-drilling the holes, fill the entire length of the hole with concrete mix. Use a trowel to make sure that the mix is even and there are no air bubbles in it.

When the concrete is dry, it will help to keep the posts from moving around when you start to put pressure on them. You may need a helper to place the posts in the concrete if they are very long or heavy.

After all the posts have concrete in the bottom of their holes, you can start to set them. Use a tape measure to measure from one end of the post to the other. You will need two people for this step.

If you are working alone, you may need to build a lever to help you move the posts into position. The lever will push against the dirt at the bottom of the hole and keep the post from falling over.

how do you level fence posts - remodelingmate.com

Putting pressure on the post

Once you have measured the first post, you can start to lever it into position. You may need to hold the post in place for up to an hour before you can go on to lever in the next one. It is very important that they all line up correctly or your fence will not be straight.

You can use a string to measure their positions if you need to.

When it comes time to putting pressure on the posts, you should start with the bottom ones first. This will help to keep the bottom row of posts from moving out of alignment. If you have a row of fence that goes at a slant, then you will need to fix each post as you come to it or your entire fence may end up being at a slant.

When you have all the bottom rows in place, check the entire fence to make sure it is straight and then go back and finish setting in the top rows.

Once the posts have all been set, you can start to attach the wood rails to them. The rails are attached to both sides of each post using galvanized fence staples. Use a tape measure to make sure that the rails are put on at the right distance apart.

When you have finished with one side, you may need to nudge some of the posts into position if they have moved out of alignment.

When the bottom rail is complete, you can start to put the second one on. You may find it easier to work on the opposite side so that the slant of the ground will help to keep the fence upright and steady as you work.

When you have finished with one side, you can start to attach the third and fourth rails on each post. When this has been done, you can stand back and admire your handiwork. If you don’t like the way it looks, then you can always take it down and start again.

If the ground is at a steep angle, you may need to make the bottom rail longer than normal. You can cut it to size later once you know the exact length that you need. You will also need more horizontal rails to support the extra weight.

Sources & references used in this article: