How do you vent a microwave through the wall?

How to Vent a Microwave Through Wall?

The first thing that you have to do is to determine what type of microwave you have. If it is a convection microwave, then you will need to get rid of the vent hole in order to prevent overheating. You may or may not have to remove the vent if you are using a convection microwave.

If your microwave is a non-convection model, then you don’t need to worry about removing the vent hole since there isn’t any air flow going through the wall. If you are not sure about what kind of microwave you have, then just read the manual that came with it.

Second, you will need to measure the height and width of the vent. These are going to be the dimensions of your new opening. The vent that you are installing is probably larger than the one that is there now so you will have to cut out some of the drywall around the outside.

Now measure the height and width of your new vent. Cut a piece of drywall to fit around the outside of the vent. You can now attach this to the wall.

Use mesh metal as a backing for the drywall to provide extra strength. You will then be able to screw the vent into place using sheet rock screws.

Once the vent is in place, then you just have to patch and paint the area around it. This can be done using mesh metal and drywall compound to patch the old hole. Once this is done you can paint the area.

Make sure that you get as much paint onto the surface as possible to ensure a good seal.

How to Install Over the Range Microwave Without Vent?

Over the range microwave installation can seem complex, but if you’re careful and take your time, you can do it yourself and save yourself a few hundred dollars. The first thing that you are going to need to do is remove your old oven. If you have gas lines or electrical wiring in the way, you should call a professional to hook up your new oven properly.

If you’ve ruled out any gas or electrical lines, then you can continue with the installation. After you’ve removed your old oven, check behind it for additional mounting hardware, which is usually two small metal brackets. If you find them, you’re ready to install your new oven.

how do you vent a microwave through the wall from our website

If you don’t find them, go ahead and place your new oven where the old one was. Then measure the space on the bottom of the oven where the brackets are supposed to go. This will be the width and height in inches (38″ W, 32″ H).

Take this information to the home improvement center and get two pieces of metal that fit the dimensions.

Before you go any further with the installation, make sure that the power is turned off to the oven at the breaker. This is an important safety step. Otherwise, you’re ready to go.

Place the metal mounting brackets behind your new oven and attach them to the oven with the enclosed screws. Place a piece of wood on the floor beneath where you will be working and place the oven on top of it. This prevents the oven from slipping when you are removing or attaching the brackets.

Now, turn your attention to the bottom of the oven. There should be three or four screws in each of the corners. Use a screwdriver to remove these.

Once they are out, you can slip the oven away from the wall. If there are any wires attached to the back of the oven, disconnect them. This will make it easier to slide the oven out.

Now that you have the old brackets out of the way, you can place the new ones into place. You then have to reconnect any wires that you disconnected from the back of the oven. When you are finished, you can slide it back into place and secure it using the screws that you removed earlier.

Be sure to test your oven after you have finished the installation. Over the range microwave installation can seem complex, but with a little time and effort, you can do it yourself and save money.

How to Install a Slide-in Oven

Installing a slide-in range can be a little challenging for the average do-it-yourselfer. If you are replacing an existing oven, it is pretty easy. If you are installing a new one from scratch, it can be a little more involved.

Before you start, if your cabinets go all the way to the ceiling, you will have to make sure you build your cabinets tall enough for the range to fit. This is usually no problem, but you don’t want to get your cabinets and then find out the oven won’t fit.

how do you vent a microwave through the wall at remodelingmate.com

After you have done this, you can start installing your oven. First, disconnect the power source to the oven if it is electric. Next, remove the oven.

If it’s a self-cleaning model, you can do this by hand. After you have removed it, disconnect the exhaust tubing on the back and pull it out.

Once you have it out of the way, measure the opening where your new oven will go. Make sure you measure the width, height and depth. Then, go to the home improvement center and get 3/4-inch plywood that matches those dimensions.

If you are installing a slide-in model, you will have to place this plywood on the bottom of your cabinets and secure it in place. Use wood screws to secure the plywood in place.

Next, place the base of your new oven on the plywood and trace around it. Now drill a hole on each corner of the tracing. These are for the mounting brackets.

After you have drilled the holes, place the mounting brackets over them. Insert a bolt into each hole and tighten them down with a socket wrench. After all the bolts are tightened down, place the oven on top of the mounting brackets.

Now you can connect the exhaust tubing to the back of the oven and refill it with whatever fuel it uses.

By using this method, you can easily and quickly mount an oven in your kitchen cabinets.

How to Install an Over-the-Range Microwave

Installing an over-the-range microwave can seem like a daunting task, but it is not that difficult if you take your time and pay attention to what you are doing.

Before you start, turn off the power to the area where you will be working. Next, remove the screws from the cabinet above your stove. There will most likely be a few light bulbs inside, so you may have to reach in and take them out before the cabinet will come off.

how do you vent a microwave through the wall - remodelingmate.com

After you have the cabinet off, you may need to disconnect some wires and plumbing. This is where a schematic of your wiring will come in handy.

Find the power source for the microwave you are replacing. If the power is off, you can just pull out the drawer and remove the drawer front. If the power is still on, you may have to disconnect some wires in order to remove the drawer.

Next, you will have to remove the plumbing. Check your schematic to see what goes where. In most cases, you can disconnect some tubing and unscrew a few screws.

Now, place the mounting bracket for your new microwave on the wall above your stove. If you have a stud finder, you can locate the studs in the wall. Then, place the bolts that came with your microwave into the mounting holes of the bracket.

Now, level the microwave and mark the holes with a pencil. Then, remove the microwave and drill holes into the wall. Be careful when drilling into the wall because you may hit a wire or pipe inside.

After you have drilled the holes, place the bolts back through the mounting holes and secure them in place with a lock washer and nut. After this is done, you can put the microwave back in place.

Connect the wiring and plumbing that you removed from the old microwave to the new one. If you have a schematic, it will tell you where each wire and tube goes. Otherwise, you will have to guess.

If you still have the cabinet above your new microwave, you can reinstall it now. Then, place your light bulbs back in and secure them. Turn on the power and test to make sure it works properly.

Once you are certain everything works, you can put the cabinet back on the wall and screw it in place. Also, you can replace the toe kick plate and trim pieces around your new appliance.

How to Replace a Blade on a Reciprocating Saw

how do you vent a microwave through the wall on remodelingmate.com

A reciprocating saw has many uses around the house, but over time the blade dulls and should be replaced. It is fairly easy to change the blade on your own. All you need is a new blade and a screwdriver to remove a few screws.

Begin by turning the saw off and removing any accessories such as a metal cutting blade. Next, remove the screws in the front of the saw that hold the two halves together. There should be one on the top and one on the bottom of the saw.

When the screws are removed, you can take the two halves of the saw apart. Be careful when you do this because the blade is under spring tension and can cause an injury if it pops out.

When the saw is apart, you will see the blade on the top of the motor connection. The blade can be removed by taking the nut off of the metal pin that is holding it in place.

After the nut is off, you can slide the blade off of the metal pin. A new blade can then be put on in the same manner. Make sure that you follow the instructions on the package for the size of blade that you are using.

When the new blade is in place, you can reassemble the saw. First, place the top half of the saw over the bottom half and line up all of the holes. Replace the screws and tighten them down in a cross pattern.

After the saw is together, you can test it to make sure it is working properly. If it is, you are ready to use it again.

How to Clean and Lubricate a Chain Saws

A chain saw is an important tool used for many things around the house from cutting fire wood to clearing out brush. A chain saw requires maintenance on a regular basis to ensure that it works properly and stays in good condition.

The first step is to read the owners manual for you model and make of saw. Different models have different requirements for maintenance. Generally, most saws will require that you clean and lubricate the bar and chain oil.

Begin by draining the old engine oil into a container. After it has been drained, refill the engine with new oil. Do not overfill the engine as this can cause it to leak and improper levels of oil can harm the engine.

After the engine has been refilled with oil you will need to let it run for a few minutes so that the new oil can be circulated throughout the engine.

how do you vent a microwave through the wall from our website

Next, disassemble the chain saw. This process will vary by model and saw but most chain saws have a few screws that hold the bar and chain onto the engine. Use a screwdriver to remove these screws.

After the screws are removed, you can take the bar and chain off of the saw. You will then need to remove the old chain oil from inside of the engine. Usually, you can do this by starting the saw and letting the engine run for a few minutes.

The heat that is produced will be enough to burn off any extra oil inside of the engine. If this doesn’t work, then heating up the engine with a propane torch will be enough to burn off any excess oil.

After the excess oil has been burned off, you can refill the tool with new chain oil. Use only the type of oil that is recommended by the manufacturer for your saw. Overfilling or underfilling the oil can cause problems with your saw.

Once you have refilled the chain oil, you will need to put a new bar and chain on the saw. Follow the instructions that came with the saw to determine the size of bar and chain that you can use. The chain will hook around the bar and be secured in place with the screws that you removed earlier.

After you have finished reassembling the saw, you should test it to make sure it is working properly.

How to Sharpen a Chainsaw

Most of the time you will not need to sharpen your chain saw. Over a period of time, the chain will either become dull or nicked. When this happens, the chain needs to be sharpened before you can continue using it.

Begin by unplugging the chain saw from the power source. This will be either the electricity or fuel that is needed to power the saw.

Sources & references used in this article: