Where is step flashing installed?

What is Roof Flashing?

Roof flashing is a type of roofing system which consists of two or more layers of metal sheeting attached to each other with screws, nails, or bolts. The purpose of the roof flashing system is to provide additional strength and protection from severe weather conditions such as hail, windstorm, lightning strikes and ice storms. Roof flashers are used when there isn’t enough space inside your home for a traditional roof covering.

Why Install Roof Flashing?

Roof flashing is generally considered one of the best ways to add extra protection against extreme weather conditions. The main reason why it’s so good is because it provides additional structural support to your house. It will also prevent water damage due to rain and snow falling onto your roof during heavy downpours. Also, if you have a tornado warning, then having roof flashing can protect your property from being damaged by flying debris.

How to Install Roof Flashing?

In order to install roof flashing, you’ll need to remove any existing siding and replace it with new material. You may also want to consider installing a second layer of roofing material over the top of the first one. This will allow for better drainage and keep your house cooler in hot weather. If you’re not comfortable doing these things yourself, then hiring someone else can make installation easier.

What are the Common Roof Flashing Mistakes?

There are many possible mistakes that you can make when installing roof flashing. One of the most common is not using enough flashing materials. This means that your house may still be exposed to the elements. The other common mistake is not having an adequate slope that directs water away from your home.

The most common flashing materials are metal and rubber. A popular metal material is copper, but it’s also very expensive. It’s a good idea to use it on your roof, but it might not be worth the cost if you’re just installing it on a small area like your roof flashing.

Another popular metal material is aluminum. This is also fairly inexpensive and is great for installing flashing on small sections of your roof. Zinc roofing is another metal flashing material that comes in sheets and is fairly cheap. It is prone to developing a greenish tint over time, but this can be easily replaced without having to replace the entire flashing system.

Metal gutters can also be used as flashing materials. They’re most often found on traditional houses with steep roofs and gabled ends. There are a couple of ways you can utilize them. The first is to have two layers of metal gutters with the seams offset from each other by about 6 inches.

This allows water to flow into the gutter, but it also protects vertical seams in case of windblown rain.

where is step flashing installed from our website

Another way is to have the metal gutters be the only layer that goes against your house. The downspout is then re-routed to go over the seam. This protects the vertical seam, but can be problematic if you get a lot of clogging in your gutters.

Sometimes, it’s just easier to use a rubber flashing material. There are many different types of rubber for roofs. The most common is EPDM and it comes in the form of a tape. This makes it very easy to install since it comes in a roll and you can cut as much or as little as you need.

Some people prefer the metal lath instead of the tape since it looks slightly better on the roof. However, you’ll need to cut each piece to size and assemble it onto your roof. This process can get very time consuming if you have a steep roof and a big house.

You can easily buy roof flashing at your local home improvement center. Before you buy anything, be sure to check the materials first to make sure they’re going to work for you.

One of the most important areas of your house when it comes to flashings is around the chimney. This can cause a lot of problems if it isn’t installed correctly and can even lead to leaks that go undetected for years.

To ensure that your flashing around your chimney is installed correctly, you can use either metal or rubber. Many people use metal lath with mastic on their chimney flashing since it’s very durable and long-lasting.

If you’re looking to save some money, you can also use a rubber flashing such as EPDM around your chimney. This is usually adequate for most chimneys since they’re not exposed to the same elements as the rest of the roof. That being said, you still need to be careful when installing it.

The biggest problem that people have with installing rubber flashing around their chimney is not cutting it correctly. The metal lath should come up the side of the chimney at a 90-degree angle. This allows for water to run down the side of the chimney and off the flashing instead of running down inside the wall. Cutting the flashing at an angle can cause water to get inside your wall.

If you have tile or brick on the side of your chimney, then it’s even more important to make sure that the flashing goes on at the correct angle.

Installing flashing around a chimney isn’t too difficult if you’re fairly handy. However, if you aren’t very handy and you’re still willing to give it a try, you can always just hire a handyman around the cost of $100-$200 to do the job.

How to Install Roof Flashing

where is step flashing installed - remodelingmate.com

Installing roof flashing is fairly easy, but you do need to take the time to make sure it’s installed correctly. One of the most important things to remember when installing roof flashing is that it must go on at a 90-degree angle, otherwise water can get inside of your walls behind the flashing.

After measuring for your first piece of metal flashing, use your tin snips to cut it to size. It’s a good idea to wear rubber gloves while you do this since the flashing can be sharp around the edges. Next, use your metal hat to tap the piece into place on the side of the wall. It should go on at a 90-degree angle and look like an upside “L”.

Once this piece of flashing is in place, take your tape measure and measure out how much flashing you’ll need for the rest of your roof. Since metal flashing comes in 10-foot sections, you’ll have to make several cuts to get the right size. Using your tape measure and a pencil, mark where you need to cut. Remember, you want the piece to fit on at a 90-degree angle just like the first piece you installed.

For each piece of flashing you install, use your metal hat to gently tap it into place along the side of the wall. Make sure the top edge of the flashing is slightly above the edge of your roof shingle. Continue this process all the way up the side of your house.

After you finish installing the flashing on the side of your house, go back and install pieces along the front and back as well.

Installing flashing around your chimney is a little different since you need to make sure there are no gaps between the wall and the flashing.

Sources & references used in this article: